Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
Beide Seiten der vorigen Revision Vorhergehende Überarbeitung Nächste Überarbeitung | Vorhergehende Überarbeitung | ||
elektronik:bcl-1 [2014/09/12 08:34] – volkerp | elektronik:bcl-1 [2014/12/18 14:13] (aktuell) – [BCL-1 remote control clock] volkerp | ||
---|---|---|---|
Zeile 4: | Zeile 4: | ||
Das ist eine Digitaluhr in einem Lampengehäuse, | Das ist eine Digitaluhr in einem Lampengehäuse, | ||
- | {{: | + | {{: |
- | Der Bausatz enthält alle Teile incl. Knopfzellen! Achtung: Es müssen auch mehrere | + | Der Bausatz enthält alle Teile incl. Knopfzellen! Achtung: Es müssen auch mehrere |
- | Kit Modell: BCL-1 | + | Kit Modell: BCL-1 \\ |
- | Betriebsspannung: | + | Betriebsspannung: |
- | Fernbedienung Größe: 86*40*6 mm | + | Fernbedienung Größe: 86*40*6 mm \\ |
Lampengehäuse Durchmesser: | Lampengehäuse Durchmesser: | ||
Zeile 33: | Zeile 33: | ||
http:// | http:// | ||
- | http:// | + | http:// |
http:// | http:// | ||
+ | ===== Operating instructions ===== | ||
+ | |||
+ | BCL-1Remote control clock specification | ||
+ | |||
+ | **1> | ||
+ | |||
+ | - Power lost memory | ||
+ | - Checking the time precisely, hourly chime | ||
+ | - Error correction | ||
+ | - Can turn off the digital display | ||
+ | - 5 channel alarm clock | ||
+ | |||
+ | |||
+ | **2> | ||
+ | |||
+ | - Kit model: BCL-1 | ||
+ | - Package name: 4 -bit remote control clock | ||
+ | - PCB size :F57mm 1.0mm thick | ||
+ | - Work voltage: 5V (Powered by USB) | ||
+ | - lamp body size: | ||
+ | |||
+ | |||
+ | **3> | ||
+ | |||
+ | The whole system is made up of MCU minimum system, infrared receiver circuit, | ||
+ | display circuit, buzzer circuit, the clock chip and power supply. | ||
+ | |||
+ | - MCU minimum system: U1(STC11F04E), | ||
+ | - Infrared receiver circuit: U3 is responsible to receive the signal that is sent by remote control. After amplification, | ||
+ | - Display circuit: | ||
+ | - Buzzer circuit: R6, Q5 and LS1,key tone of the clock, the sound of hourly chime, the bell of clock. Sound is output from P3.1 port of MCU and make a sound by Q5 driving LS1 | ||
+ | - Clock chip: | ||
+ | - Power Supply: J1 connect power line and C4 smoothing. | ||
+ | |||
+ | |||
+ | **4> | ||
+ | |||
+ | **A General function of keys: ** | ||
+ | |||
+ | the key in the center is main menu; The increase key and decrease key control " | ||
+ | |||
+ | - The **submenu of adjusting time**: the place where twinkles on digital tube is currently selected. By pressing the keys of “increase” “decrease” “left and" “right" | ||
+ | - **Submenu of setting alarm clock**: First, it is the choice of main switch of 5 channel alarm clock. The first bit displays C and two bits at the end when flash will display ON or OFF. It is switched by the keys of “increase” “decrease" | ||
+ | - **Submenu of error correction**: | ||
+ | |||
+ | **B The quick operating function of key ** | ||
+ | |||
+ | - Under the normal walking hour interface, press the key of “shutdown" | ||
+ | - Under the normal walking hour interface, press the key of “shaking head" can switch the interface between hour or minute interface and minute or second interface. | ||
+ | - Under the normal walking hour interface, press the key of “turn speed" can choose ON or OFF of whole 5 channel alarm clock. After setting well, press the key in the center to enter the choice of ON or OFF about the function of hourly chime. Then press the key in the center and return to the normal walking hour interface | ||
+ | - Under the minute and second walking hour interface and display SEC. The second bit flashes, a few seconds later, the minute and second flash together. And according to the accurate time, press the key “time" |